ATX 3.0 PCIe 5.0 12VHPWR Cable 2x8 Pin to 16 600W GPU Power Cord, Type A 4-Pin on Bottom, 16AWG 60cm (24in), for EVGA G7/G6/G5/G3/G2/P2/T2 & Super Flower Leadex Titanium/Platinum/III Series

Prices from
10.99

Sponsored links

COMPARE ALL WEBSHOPS (1)

Description

Amazon 🔹 TYPE A — 4-PIN ON BOTTOM | VERIFY BEFORE ORDERING ⚠️ This is the Type A configuration: the 4-pin sense wires are positioned on the bottom side of the connector (closer to the GPU PCB). Optimized for graphics cards with thick backplates or limited clearance above the power connector. ⚠️ Type A and Type B look similar — verify your GPU orientation before ordering. Type B (4-pin on top) available for different layouts. 🔹 PRECISE EVGA/SUPERFLOWER COMPATIBILITY — VERIFY YOUR PSU MODEL FIRST ⚠️ Designed exclusively for EVGA/SuperFlower modular PSUs with 8-pin modular ports: G7/G6/G5/G3/G2/G1+/GA/GM/GT, P+/P6/P5/P3/P2/T2, B5/B3, PQ/PS/GS, SuperFlower Leadex Titanium/Platinum/III. ⚠️ NOT compatible with: EVGA GQ series (650GQ/750GQ/850GQ/1000GQ), 1000PS/850GS/1050GS, or any Corsair/Seasonic/Thermaltake PSU. Using this cable with an incompatible PSU WILL damage your hardware. 🔹 90° ANGLED — REQUIRES ONLY 18-20MM CLEARANCE The 90-degree angled 12VHPWR connector reduces clearance requirements to just 18-20mm above the GPU power port, compared to 35mm+ for straight connectors. Solves side panel clearance issues in small form factor cases and full-tower builds with tall GPUs. No adapter needed — direct PSU-to-GPU connection. 🔹 16AWG WIRE — FULL 600W SUPPORT — BOTH 8-PIN ENDS REQUIRED ⚠️ Constructed with 16AWG wire for full support of 600W power delivery to RTX 4090/4080/4070/3090Ti and other PCIe 5.0 GPUs with 12VHPWR 16-pin (12+4 pin) ports. ⚠️ Both 2x 8-pin connectors MUST be plugged into your PSU — using only one 8-pin end will NOT provide sufficient power and may cause system instability or damage. 60cm length for clean cable routing. 🔹 FACTORY-TESTED — SAFE & RELIABLE Each cable undergoes strict factory continuity, pinout, and high-current testing. Premium terminals with high-current single-split 4-spring design for stable contact. ⚠️ Turn off PC power and unplug the power cable before installation. Do NOT force connectors — align the keying and push until fully seated. ⚠️ IMPORTANT NOTES: Type A only — 4-pin on bottom. Verify GPU orientation before ordering. EVGA/SuperFlower 8-pin modular ports ONLY. NOT for GQ/1000PS/850GS or non-EVGA/SuperFlower PSUs. Both 2x 8-pin ends MUST be connected. Using only one end may cause damage. 90° connector requires minimum 18-20mm clearance above GPU power port. Turn off PC power and unplug before installation. Do not force connectors.

Compare webshops (1)

Sponsored links · Some shops pay us a fee

Sort by:

£ 10.99

Description (1)

🔹 TYPE A — 4-PIN ON BOTTOM | VERIFY BEFORE ORDERING ⚠️ This is the Type A configuration: the 4-pin sense wires are positioned on the bottom side of the connector (closer to the GPU PCB). Optimized for graphics cards with thick backplates or limited clearance above the power connector. ⚠️ Type A and Type B look similar — verify your GPU orientation before ordering. Type B (4-pin on top) available for different layouts. 🔹 PRECISE EVGA/SUPERFLOWER COMPATIBILITY — VERIFY YOUR PSU MODEL FIRST ⚠️ Designed exclusively for EVGA/SuperFlower modular PSUs with 8-pin modular ports: G7/G6/G5/G3/G2/G1+/GA/GM/GT, P+/P6/P5/P3/P2/T2, B5/B3, PQ/PS/GS, SuperFlower Leadex Titanium/Platinum/III. ⚠️ NOT compatible with: EVGA GQ series (650GQ/750GQ/850GQ/1000GQ), 1000PS/850GS/1050GS, or any Corsair/Seasonic/Thermaltake PSU. Using this cable with an incompatible PSU WILL damage your hardware. 🔹 90° ANGLED — REQUIRES ONLY 18-20MM CLEARANCE The 90-degree angled 12VHPWR connector reduces clearance requirements to just 18-20mm above the GPU power port, compared to 35mm+ for straight connectors. Solves side panel clearance issues in small form factor cases and full-tower builds with tall GPUs. No adapter needed — direct PSU-to-GPU connection. 🔹 16AWG WIRE — FULL 600W SUPPORT — BOTH 8-PIN ENDS REQUIRED ⚠️ Constructed with 16AWG wire for full support of 600W power delivery to RTX 4090/4080/4070/3090Ti and other PCIe 5.0 GPUs with 12VHPWR 16-pin (12+4 pin) ports. ⚠️ Both 2x 8-pin connectors MUST be plugged into your PSU — using only one 8-pin end will NOT provide sufficient power and may cause system instability or damage. 60cm length for clean cable routing. 🔹 FACTORY-TESTED — SAFE & RELIABLE Each cable undergoes strict factory continuity, pinout, and high-current testing. Premium terminals with high-current single-split 4-spring design for stable contact. ⚠️ Turn off PC power and unplug the power cable before installation. Do NOT force connectors — align the keying and push until fully seated. ⚠️ IMPORTANT NOTES: Type A only — 4-pin on bottom. Verify GPU orientation before ordering. EVGA/SuperFlower 8-pin modular ports ONLY. NOT for GQ/1000PS/850GS or non-EVGA/SuperFlower PSUs. Both 2x 8-pin ends MUST be connected. Using only one end may cause damage. 90° connector requires minimum 18-20mm clearance above GPU power port. Turn off PC power and unplug before installation. Do not force connectors.


Product specifications

Brand lilila-ree
EAN
  • 0774388286553
Color
  • Black

Featured Choice
£ 10.99
To Shop