SpeedBox 3.3 Compatible with Giant E bikes/Tuning chip for SyncDrive Pro Motors and RideControl Go 2022 2024

Speedbox Giant 3.3 Speed Increasing Device. Unleash the full potential of your Giant e-bike with the SpeedBox 3.3! This advanced tuning chip disables the factory speed limit, allowing you to ride at speeds of 50 km/h and beyond. Unlike other devices, the SpeedBox 3.3 continues to show accurate, real-time data like maximum speed, mileage, and range on your display. Easily activate or deactivate the chip using the WALK function or a simple button combination. You can even set your own custom speed limit for the ultimate personalized ride. Compatible with Giant SyncDrive Pro 2 & Sport 2 motors. The SpeedBox 3.3 chip disables the bike´s speed limit. After installing the chip, you can view real-time values such as maximum speed, average speed, daily mileage, and range.Features:How does SpeedBox 3.3 work for Giant:- Activation/deactivation should always be done before riding, not during the ride.- To activate the SpeedBox chip, briefly activate the WALK function on the e-bike´s control unit. The e-bike´s display will briefly show 5.0 km/h (3.1 mph), and from then on, you can ride at a speed of 50 km/h. You can change the default speed limit to any limit (up to 99 km/h), but to minimize the risk of error codes, we recommend not exceeding 50 km/h.- To deactivate the chip function, reactivate the WALK function. The display will show 2.5 km/h (1.6 mph), and the 25 km/h speed limit will be activated again. The e-bike operates the same as before installing the chip.- We´re also prepared for e-bikes that don´t have a classic control panel with a Walk button. In this case, simply use the button combination - + - + to activate SpeedBox. You can also deactivate it.- To set the maximum speed, you can switch between the following modes: Turbo - EMTB - Tour - Eco - Tour - EMTB - Turbo. The current speed limit will then be displayed. To change the maximum speed, briefly press the WALK button or turn the wheel 360°. 1.5 km/h on the display corresponds to the 15 km/h limit, 2.0 corresponds to the 20 km/h limit, 2.5 corresponds to 25 km/h, 3.0 corresponds to 30 km/h, 5.0 corresponds to 50 km/h, etc. The last displayed limit is saved after five seconds of inactivity.- When using the SpeedBox, the e-bike must be switched on after the end of the ride until the display shows a constant 0.0 km/h. During this phase, the display will show the remaining time. You can then safely switch off the bike and look forward to the next ride.- If you want a SpeedBox on a new bike, you must first ride at least 10 km.Specifications:- Maximum speed: Unlimited (We recommend not exceeding the preset limit of 50 km/h)- Speed Limit Setting: Yes- Values on the screen: Real-time valuesActivation/deactivation:- Walk function- Button combination - + - +Compatible with:- SyncDrive Pro 2 (85 nm) and RideControl Go- SyncDrive Sport 2 (75 nm) + RideControl Dash. tradeinn Bikeinn

Tuning chip to remove the speed limit on e-bikes. Compatible with motos: SyncDrive Pro 2 (85 Nm) and RideControl Go, SyncDrive Sport 2 (75 Nm) + RideControl Dash, SyncDrive Sport 3 (85 Nm), SyncDrive Sport 3x (100 Nm). You can set your own speed limit. Activation/deactivation: Do not perform while driving. By pressing the walk button, the e-bike display shows a value of 5.0 km/h (3.1 mph) - you can ride at speeds of up to 50 km/h or more. To minimize the risk of error codes, we recommend not to exceed 35 km/h. Disable tuning in the same way, and your display will show 2.5 km/h (1.6 mph). If your e-bike does not have a walk button, use the combination of - + - + + buttons to activate/disable the SpeedBox. After finishing the ride, leave the e-bike on until the value is 0.0 km/h. During this process, the remaining time is displayed. Do not remove the display to lock the e-bike until the SpeedBox has completed the "countdown" process. Do not perform a firmware update of your e-bike to avoid the risk of tuning detection. The warranty for SpeedBox products does not apply to malfunctions caused by an update of the engine. For short stops, leave one foot on the pedal so that the countdown does not begin and you can continue driving. For longer stops, allow at least part of the countdown. After a long journey, the countdown can take several minutes. Do not remove the display if the countdown is not complete. Before installing the SpeedBox into a new e-bike, ride at least 10 km with this e-bike. E-bikes equipped with SpeedBox must not be used on public roads, bike paths or public places. Detailed installation information can be found here: https://www.youtube.com/embed/uRzOhp0qzB0